Precautions when cleaning the outside of the tanker
    The steps of external cleaning of the tanker are as follows: 1) Remove the silt on the surface of the car body, select appropriate water column pressure, moisten the entire vehicle first, make the sediment permeate moisture, easily fall off, and then from top to bottom and front to back rinse. 2) Spray special scrubbing liquid to scrub. Add the proper amount of detergent to the foam cleaner, turn on the power supply, adjust the output pressure, spray the foam cleaning solution on the entire body surface, and wait for 1-2 minutes, then gently wipe it with a clean suede, sponge or towel. wipe. 3) Wash the foam with clean water. Use a high-pressure car washer or tap water to wash away the foam car wash that remains on the car body surface. 4) Wipe the surface of the car body with water. First use a suede to absorb water stains on the body, then use compressed air to dry the body exterior.
Although the tank truck cleaning operation is relatively simple, it must be operated in accordance with the specifications to improve work efficiency. In the car wash operation, the following points should be noted. 1) Special car washes should be used. Do not use soap or detergent. Because of the strong alkalinity of this kind of product, it will cause the paint surface to lose its light, the local color difference, the aging of the sealing rubber, and it will also accelerate the metal corrosion of the part where the paint is peeled off. . 2) Before high-pressure flushing, it must be checked whether the window and the front and rear covers are closed properly. 3) When high-pressure flushing, the water pressure should not be too high, generally not higher than 0.7MPa. In addition, the entire vehicle should be washed with scattered sprays of water and then flushed with concentrated water. For pressure-adjustable washers, the water pressure may be higher when the chassis is flushed so that the sludge and other attachments attached to the chassis can be washed away. When the vehicle body is cleaned, the water pressure can be lowered. If the water pressure of the cleaning body is too high and the water flow is too large, dirt particles can scratch the paint layer.
4) Use a soft towel or sponge when cleaning the cleaner. It is best to use a sponge to avoid scratching the paint with hard particles. 5) Use temperature-controlled washing machine, pay attention to the hot water temperature should not be too high, so as not to damage the paint layer. 6) The car wash process should follow the principle of top-down. 7) Do not wash your car in direct sunlight. 8) Do not wash the car in cold weather. Use water droplets to freeze on the car body. This will cause the paint layer to break. Car washing should be performed indoors during the cold season in the north. 9) It is found that the body of the oil tanker is accompanied by dust or impurities and should be promptly removed to avoid contamination of the paint surface.
We mainly export motorcycles (200CC, CG200, GN200, CGL200, and CM200), tricycles, scooters, engines and parts. Those brake system are drum or disk brake, rear drum brake which are strong front shock and rear shock. The CG200 is popular model. Different types of motorcycles have different dynamics and these play a role in how a Motorcycle performs in given conditions. Motorcycle fuel economy varies greatly with engine displacement and riding style. Engines are 150cc single-cylinder. The motorcycles are 4 strokes, air-cooler, and spoke or alloy wheel. Max speed Max speed about 95 km/h. Gasoline 90# or above. It starts method kick and electric and the compression ratio is 9.2:1. One muffler, bore and stroke 63.5 x 62.2mm, max output power is 9.5/7500 kw/rpm. Motorcycle tyres have Large influence over handling as the front tire size: 2.75-18/3.00-18, rear tire size is 3.00-18/ 110/90-16.
200Cc Motorcycle,200Cc Off-Road Motorcycle,Sport 200Cc Motorcycle,200Cc Super Motorcycle
JIANGMEN CHANGHUA GROUP CO., LTD. , http://www.changhuagroup-motor.com