Chen Guorong (Jiangxi Fuel Injection Pump Maintenance Professional Committee) has a 4125 engine. According to the driver, the engine will gradually go from high speed to low speed after a while, until it automatically shuts off. Exclude the air in the pump from starting again, and then turn off automatically. Check the oil circuit, according to the conventional oil pump to the tank's oil circuit, tubing, mats are drivers to change the new, just use the hand pump to pump oil, the oil pump air will be finished. No oil leakage was found in other oil paths, mats, and filter elements, and there was no fault after inspection. Then the air in the oil pump came from where it came from. The car was checked again. When the engine speed was not normal, the cylinder was turned off. One of the cylinders was not working. The high pressure fuel line was removed and the air in the nozzle was discharged. After the cylinder was broken, the engine did not stall. Instead, the speed increased until it operated normally. Therefore, the air in the oil pump was determined because the fuel injector stuck and the air in the cylinder was reversed by the fuel injector. The air filled the oil pump chamber, so that the engine could not be supplied with oil and the engine was turned off. The injector was removed and replaced. After the new nozzle is installed, the vehicle is started and everything is normal.
Reason why VE pump can't cut off oil Xu Shixiong (Jiangxi Province Spraying Pump Maintenance Professional Committee) has a VE distribution pump for Isuzu truck sent to our office for maintenance. The oil pump cleaning has a clean appearance, and it is directly on the test bench to find: the position of the oil pump at the full throttle position. At lOOOr/min, the oil volume is 22ml/2 times. Adjust the oil limit screw, the change in the amount of oil is not obvious, all the oil limit screw is withdrawn, and the amount of oil remains unchanged. Where exactly does the problem occur? When the pump is disassembled and checked, the plunger control sleeve moves flexibly. Both the K and KF values ​​are within the specifications and the orifice of the governor sleeve is not blocked. Change the new pump. Try it for the first time, still can't cut off the oil at idle speed. After the above tests and inspections, the root cause of the failure is certainly not in the pump oil part, nor in the oil and oil return passages, and the only possible problem is in the speed regulation component. Put the oil pump back on the test bench and remove the speed control spring to directly test the idling oil supply. As a result, it was found that there was still no way to cut off the oil at idle speed.
The problem is very clear, that is, there is a problem with the speed cradle assembly. So change the new speed cradle assembly. According to the technical specifications of the commissioning pump, idling fuel cut sensitive, all technical parameters have reached the required requirements.
The brake disc is composed of steel plate, adhesive heat insulation layer and friction block. The steel plate is applied to resist rust. In the painting process, smt-4 furnace temperature tracker is used to detect the temperature distribution in the coating process to guarantee the quality. The heat insulation layer is composed of non-heat transfer materials for the purpose of heat insulation. The friction block is composed of friction materials and adhesives. When braking, it is squeezed on the brake disc or brake drum to generate friction, so as to achieve the purpose of decelerating the brake. As a result of friction, the friction block will be worn gradually, generally speaking, the lower the cost of brake block wear faster.
Tower Crane Brake Disc is used for tower crane motors. To divide in function , there are hoisting brake disc, trolleying disc brake pad and slewing motor brake disc. Tower Crane Brake Disc is the easy wearing spare parts, therefore the quality of the Brake Disc is very important. BQ provides good quality Brake Disc, which is composed of steel plate, adhesive heat insulation layer and friction block. The steel plate is applied to resist rust.
Crane Brake Pad,Crane Brake Disc,Disc Brake Pad,Tower Crane Brake Disc,Motor Brake Disc,Hoisting Brake Disc
SHEN YANG BAOQUAN BUSINESS CO., LTD , https://www.sytopkittowercrane.com