弑iB I Innovation and product development In the vast northern and western regions, the wind resources are abundant. I used the 12V and 90W AC permanent magnet generators produced in Henan to be converted into wind power generation methods.
The structure of the machine is magnetic pole, the output rated voltage is 12V, the rotational speed is 500 rpm, and the wind power generation speed is 450 rpm. There are two ways to convert 12V and 90W generators: the first is that the windings of the original machine are unchanged, and the three channels are connected in parallel, see expansion. The second is to see six windings in series. If the motor coil is damaged, the 6 coils of 2 are each wound with a diameter of 0.69 enameled wire 120. The output current of the middle motor is three times that of the motor output current, and the output voltage is 1/3, that is, the high current output is the 篼 voltage output.
Generator and revolving body, the combination of the two into one whole, 36 (movable in the range. Can be composed of scrap small rubber wheel hub and shaft, or 1.5cm long iron pipe 30cm and 1.2 inch iron pipe length 40cm, 1.5 inch iron pipe One end is sealed (welded with an iron plate) and a pressure bearing is placed inside. The 1.2-inch tube is inserted into the 1.5-inch tube, and the fan is fixed on the rotating body for assembly.
The tail wing, its role is to adjust the wind direction, the tail wing beam is 120crn, 3x3 angle iron, the tail plate is composed of 40cmx40cm and the thickness is 1mm iron plate.
10cm thick 0.5-1.0cm iron plate, a small hole in the middle can put the generator shaft, two small holes on each side.
3cm fruit pine board (or other material board), based on one of the 3cm thick ribs, the windward side is cut with an axe 2cm in a slant shape, flipped over and another 3cm thick rib is cut 1cm in a slant shape into a leeward Face, drill two holes at each end of the blade, and connect with the iron plate, facing the wind in front of the wind, the leeward side is behind, and then screwed on the motor shaft, see.
20cm) is about 6m long, buried underground lm, pulling three wires with a mutual angle of 120 degrees to be stable, installed in the unobstructed wind.
Motorcycle battery charging, wireless phone, remote cordless phone battery charging.
Wind and resource-rich farming and pastoral areas can be used for lighting to watch TV.
Agricultural vehicle 654 tow machine, in the end of October, the end of the second year of the second year of the second half of the year, the farmer is idle, 3-4 times a year to the repair department, the cost is about 60 yuan, sometimes forgotten to cause battery damage, simple fan cost nearly 100 yuan With this technology, you can avoid the worry of battery charging. The wind is strong, the battery is full and can be used for lighting, making full use of natural energy.
Saddle welding procedure requires the use of a Saddle Fusion tool. This tool must be capable of holding and supporting the pipe, rounding the pipe for proper alignment between the pipe and fitting, holding the fitting, and applying and indicating the proper force during the heat fusion jointing process. The heating and fusing process must be performed with accuracy and efficiency, especially when fusing to a pressurized main pipe. Automatic saddle welding machines with CNC control system promise operator to follow the welding temperature, welding time and jointing pressure after choosing welding standard, pipe size and material. CNC HDPE reducing tee saddle fusion welding machine, which is produced under a high technology with special design of pipe fusion machines, has the principle of working on the logic of the hydraulic system. For high quality reducer and high accuracy and working efficiency, Wuxi Yuda MRH-A Automatic HDPE Fitting Reduing Tee Saddle Fusion Equipment is your best choose.
Automatic Saddle Welding,Saddle Welding,Saddle Fusion Welding,Saddle Welding Equipment
WUXI MEIERTE MACHINERY TECHNOLOGY CO.,LTD , https://www.pipefusionweldings.com