Yesterday, Lithium source electric vehicle off-line ceremony was held in Changchun. Next month, 20 pure electric buses will be supplied to Liaoyuan City to serve as city buses and buses to and from Changchun. This batch of electric buses and cars is the first batch of electric vehicles in our province.
Car sample
There is no exhaust pipe at the rear
At the ceremony, samples of electric buses and cars were placed. Open the front cover of the engine of the car, there is no configuration of the engine of the traditional car, but blocks of blue batteries. There is no exhaust pipe at the rear of the car to achieve "zero carbon emission".
"These electric buses and cars are the first electric vehicles to be mass-produced offline in our province. Electric vehicles will be the main representatives of future new energy sources," said Cai Qingsong, vice president of China Lithium Source Investment Group.
The highest speed
Bus 120 km Car 150 km
At present, the electric cars they produce can be broadly divided into two types. One is a pure electric bus co-produced with “2nd Steamer†and sells for 1.1 million yuan each, with a top speed of 120 km/h. The other is to cooperate with FAW. The Pentium model of electric cars, priced at 180,000 yuan, a top speed of 150 kilometers per hour. According to related policies, when purchasing electric buses, the relevant departments will subsidize 500,000 yuan for each vehicle and 60,000 yuan for each car.
Save energy and save money
Electric buses can save 200,000 a year
“In this way, the price for purchasing an electric vehicle will be about the same as the price for purchasing the same type of fuel vehicle, or even cheaper.†Cai Qingsong calculated an account, taking an electric bus as an example, assuming that it travels 300 kilometers a day, after many arguments, The cost of a year is about 200,000 yuan less than that of a fuel truck. "In the first quarter of next year, we plan to produce 1,000 electric Pentium cars. We will strive to achieve a production scale of 3,000 vehicles in three years," said Cai Qingsong.
Facilities
Has produced "recharging and running" car charger
Although the electric model is environmentally friendly, can the relevant configuration meet its development? “We have considered building some charging stations. What can we do if some cars have no electricity at halfway? Therefore, we have already produced a car charger that is 'charged and gone'. As long as there is a nearby power supply, it can be charged by plugging it in. "Cai Qingsong said that the capacity of the battery is tailored to different models and uses. It is fully charged in 3 hours, pure electric passenger cars can run 300 kilometers, and pure electric cars can run 400 kilometers."
Pure electric car
100 kilometers to save money 30 yuan
Taking a car as an example, the same car will consume at least 6 liters of gasoline for 100 kilometers, and the cost will be around 36 yuan. The pure electric car 100 kilometers 8 to 10 degrees of electricity, the cost of 6 yuan.
Top speed 150 km
3 hours full charge
Can run 400 kilometers at a time
Zero row of carbon
Water/Wet type wire drawing machine
LT23-25/288 water tank wire drawing machine
(1) Main technical parameters:
1. Maximum incoming line strength: ≤ 1400Mpa;
2. Drawing passes: 23, 25;
3. Maximum incoming wire diameter: 1mm;
4. Minimum outlet diameter: 0.1-0.12mm;
5. Maximum drawing speed: 15m/s;
6. Average pass compression ratio: 14%;
7. Motor power: 15-18.5kw.
(2) Equipment composition for wet wire drawing machine
1. The frame is formed by welding section steel, and the tank body is formed by welding stainless steel plate;
2. The tower wheel is made of 45 steel, the working surface is sprayed with tungsten carbide powder (WC), the surface hardness is ＞ HRC60, the surface finish is 0.4Ra, and the service life is more than two years;
3. The machine coefficient is large in the front and small in the rear, which is conducive to improving production efficiency and continuous production;
4. Both the mold base and the mold base have angles, and the steel wire is always in a straight line during drawing, which is conducive to improving the quality and not easy to break the wire;
5. Tower wheel and mold are cooled by immersion in self circulating lubricating coolant;
6. The transmission mode is driven by synchronous belt to eliminate oil leakage and reduce noise;
7. The main bearings are made of NSK brand from Japan, and the motors are frequency conversion motors;
8. The finished product mold is installed in the mold base that can adjust the angle, which is conducive to the alignment of the finished product reel and the adjustment of the product ring diameter;
9. Box overturning force ≤ 200N;
10. All wire passing wheels and rollers are subject to quenching treatment, with surface hardness ＞ HRC50;
11. AC frequency conversion speed regulation is adopted, and the frequency converter adopts Siemens or Huichuan brand;
12. The electric control mode is PLC control, and the PLC is made of Mitsubishi or Siemens;
13. The touch screen is Taiwan made color touch screen, and low-voltage electrical components are all domestic well-known brands;
14. The machine is equipped with inching, front and rear linkage, start, stop and other functions. The human-machine interface of the main operating console has the functions of length, speed preset display, fault query, and equipment status display;
15. The electric cabinet is a standard cabinet produced by professional enterprises.
Water/Wet Type Wire Drawing Machine,Water Type Wire Drawing Machine,Wet Type Wire Drawing Machine,Water Tank Wire Drawbench
Jiangyin Wanyi Machinery CO.,Ltd , https://www.wydrawmachine.com