High Pressure Hydraulic Oil Hand Pump

Operation:
1. insert the standpipe into the bung of the barrel,then thread the lower part of the bung adapter onto the bung-hand tighten only.
2. Slide the top part of the bung adapter down over the top of the lower part and hand-tighten it to secure the standpipe in place.
3. When ready to pump,rotate the handle clockwise to begin the flow of fluid.
Use attention:
1.we suggest for Dispensing Oil,gasoline, kerosene, diesel fuel and low viscosity oil .
2.Hand's rotation direction like(1)Main engine(pump part)upside arrow instruction direction operation.
3.Wrong use of drugs,saline, etc.,Please immediately oil in clean pump bodies and so on use the lamp oil,to clean.
4.To choose the ground oil tank, etc.,to avoid the rain, dew,sunlight and easy to fire and other places, in accordance with the provisions of the Fire Services Act.
5.Please note that this machine if you do not comply with the warnings and precautions for use, and injury and the accident occurred, is not responsible for manufacturers.
6.Please note that unauthorized modification of the machine, using the wrong method of failures of accidents, as well as all other improper operation,is not responsible for manufacturers.
Suitable for a variety of conditions: suitable for all quality quality conditions, this hand pump can be used, as long as quality extraction of oil does not freeze!
   7.Can not be extracted water and acid and alkali chemical solution!




 
Operation:
1. insert the standpipe into the bung of the barrel,then thread the lower part of the bung adapter onto the bung-hand tighten only.
2. Slide the top part of the bung adapter down over the top of the lower part and hand-tighten it to secure the standpipe in place.
3. When ready to pump,rotate the handle clockwise to begin the flow of fluid.
Use attention:
1.we suggest for Dispensing Oil,gasoline, kerosene, diesel fuel and low viscosity oil .
2.Hand's rotation direction like(1)Main engine(pump part)upside arrow instruction direction operation.
3.Wrong use of drugs,saline, etc.,Please immediately oil in clean pump bodies and so on use the lamp oil,to clean.
4.To choose the ground oil tank, etc.,to avoid the rain, dew,sunlight and easy to fire and other places, in accordance with the provisions of the Fire Services Act.
5.Please note that this machine if you do not comply with the warnings and precautions for use, and injury and the accident occurred, is not responsible for manufacturers.
6.Please note that unauthorized modification of the machine, using the wrong method of failures of accidents, as well as all other improper operation,is not responsible for manufacturers.
Suitable for a variety of conditions: suitable for all quality quality conditions, this hand pump can be used, as long as quality extraction of oil does not freeze!
   7.Can not be extracted water and acid and alkali chemical solution!




 

Welded Bed Plate For Flanges Of Ship Pipe

The flange welded single-sided seat plate is mainly installed on the top, side wall and bottom of the cabin or cabinet as the entrance and exit of the cabin or cabinet. Valves, accessories or pipes can be installed directly on the single-sided seat plate.

Flange welded single-sided seat plate is suitable for seawater, fresh water, oil, air and steam pipelines below 300 °C. The commonly used nominal diameter is 15~150 mm, and the nominal pressure is lower than 1.6 MPa. The shape of the single-sided seat plate is similar to the corresponding lap-welded Steel Flange.

Flange welded double-sided seat plates are generally used when pipelines pass through decks and tanks, and the two sides of the seat plate are respectively connected to valves, accessories or pipes.
Compared with the single-sided seat plate, the double-sided seat plate has an extra shoulder and double-sided mounting stud bolts. The outer diameter of the shoulder is 10~20 mm larger than that of the corresponding flange, and the thickness of the shoulder is 6~12 mm.
Its scope of application and other structural dimensions are basically the same as those of the single-sided seat plate.
The manufacturing and installation methods of the flange-welded double-sided seat plate are basically the same as the single-sided seat plate, but when the screw holes are drawn, the positions of the upper and lower screw holes of the seat plate must be staggered from each other and must not overlap; deck or bulkhead The diameter of the hole on the top is 2~3 mm larger than the diameter of the seat plate.

Welded Bed Plate For Flanges Of Ship Pipe,Flanges Of Ship Pipe Welded Bed Plate,Welding Base Plate Flange Of Ship Pipe,Ship Pipe Welding Base Plate Flange

Fuyuan Marine Accessories Co., Ltd , https://www.fuyuanmarineparts.com