1. It is best not to sterilize different types of items at the same time, such as dressings and solutions, rubber and equipment. In order to avoid misunderstandings, good results cannot be obtained.
2. Check the water level indicator every time you heat and see if there is enough water. If the water level is too low, the water tank must be replenished immediately. During the sterilization process, if the water level alarm indicator on the meter box is found to be on, the water level must be checked immediately. If the water level is too low, the main valve knob should be turned off and the total valve knob should be turned to the “full row†position to completely drain the sterilizer steam. , to be jacketed and sterilized indoor water supplement. Then press the low water level reset button on the right side of the electrical box. At this time, the alarm indicator will also go out and continue heating.
3. The sterilizer should pay special attention to whether the conductive column in the water level meter is in the middle of the water level glass tube. If it is skewed, it will cause the conductive column in the water level glass tube to fail to produce a normal effect. Even at a low water level, the power cannot be cut off immediately. At the same time, always look at the tip of the conductive column for scale formation. Since scale increases resistance, it should be removed to avoid accidents.
4. When the steam enters the sterilizing chamber, the valve in the front section of the condensate drainer should be opened gradually so that the condensate drainer can intermittently discharge the air and condensate from the sterilization chamber to ensure the sterilization effect.
5. Safety valve lifting handle should be pulled 1 or 2 times a week to keep it flexible.
6. The electric heating of the electric heating pipe joints should always be checked and tightened to prevent loosening and overheating.
7. The sterilizer should be kept clean and dry, especially when not in use, it should be wiped clean to avoid corrosion.
8. The sterilizer should be operated under complete conditions and regularly maintained so that normal operation can be performed to avoid accidents.
9. Flushing: The syringe should be removed, re-brushed, dried, packaged, and then autoclaved; the kits and dressings should be allowed to dry before re-autoclaving.
10. Cold air mass: The remaining air should be drained, drained completely and then sterilized according to the sterilization procedure.
11. When the water is cut off:
1 ) Sterilize spare items in advance.
2 ) Dispensing spare syringes and various equipment packages, infusion bottles and other items.
3 ) The recovered syringes, infusion bottles, funnels, instruments, etc. shall be soaked in fresh water until they are to be washed.
4 ) The recovered needle is rinsed with back-water and boiled for treatment.
Shangyu Xingxing Instrument Equipment Co., Ltd. is located in Daosu Town, Shangyu District, Shaoxing City, Zhejiang Province. It is a company integrating production, product research and development, processing and trading. The company's main products: series drying oven, incubator series, laboratory muffle furnace series, distilled water series, as well as clean bench, air shower, fume hoods, biological safety cabinets and other complete sets of purification equipment.
The company has a strong technical R & D team, a strong after-sale protection service system, is the leader in China's laboratory complete sets of equipment manufacturers, welcome customers to buy.
External Skeleton Extraction Arms
1. Product description:
External extraction arm is a kind of dust and smoke extraction arm with supporting outside. It can be used for fume extractors to capture dust and smoke at source.
2. Moland Product Series
Portable Fume Extractor series: MLWF50, MLWF70, MLWF100, MLWF360, MLWF120, MLWF200, MLWF280-basic, MLWF280S, MLWF290, MLWF300, MLWF300A, MLWF350, MLWF350D, MLWF400, etc.
Stationary fume extractors: MLWF350-dust bucket type, MLWF500-6T, MLWF500-6T dust bucket type, MLWF500-9T, MLWF800, MLWF800-dust bucket type, MLWF1000, MLWF1500, MLWF2000, MLWF3000, MLWF3500, MLWF4000). The electric control cabinet can be seperated from main equipment for convenient operation when the main equipment is placed outdoors.
Grinding dust extractors: MLWF100D, MLWF150D, MLWF200D, MLWF320-DM, MLWF180, MLWF380, MLWF480) and grinding cabinet (MLWF900). The grinding cabinet is usally equipped with telescopic or fixed grinding room, to form a semi-closed space to control dust and smoke spread. It also improves the filtration efficiency with low air volume and energy consumption.
VOCs treatment
3. R&D
In order to provide advanced products, our R&D department develops 3 to 5 new products every year, and irregularly improves the performance, appearance, and installation methods of existing products.
4. Certification
All our products are approved by CE, ISO9001, ISO14001, utility model patent, design patent, Program copyright, etc.
5. Exhibition
Moland participates at least 5 industry exhibitions each year.
6. Central Fume Extraction System
1) Cantilever type fume extraction system
Cantilever dust removal can be used for manual welding conditions where the work stations are evenly distributed and the span is small. The smoke and dust generated by each welding station can be effectively absorbed at the dust generation point, and will not pollute other parts of the workshop. The skeleton of the suction arm is similar to a human arm and can hover in a space within a certain length. The outer layer of the suction arm is a temperature-resistant hose, which not only prevents the hose from being burned by sparks, but also ensures the flexibility of the movement of the suction arm. A unique rotating structure is designed on the position of the Suction Hood to ensure that the suction hood can be aligned with the welding position in any orientation, so that the suction arm can effectively capture the smoke and dust generated during the welding process. The advantage of the suction arm capture is that it can be close to the place where the smoke is generated, and the collection effect is better.
2) Hood suction type fume extraction system
Cantilever dust removal can be used for manual welding conditions where the work stations are evenly distributed and the span is small. The smoke and dust generated by each welding station can be effectively absorbed at the dust generation point, and will not pollute other parts of the workshop. The skeleton of the suction arm is similar to a human arm and can hover in a space within a certain length. The outer layer of the suction arm is a temperature-resistant hose, which not only prevents the hose from being burned by sparks, but also ensures the flexibility of the movement of the suction arm. A unique rotating structure is designed on the position of the suction hood to ensure that the suction hood can be aligned with the welding position in any orientation, so that the suction arm can effectively capture the smoke and dust generated during the welding process. The advantage of the suction arm capture is that it can be close to the place where the smoke is generated, and the collection effect is better.
3) Room tupe fume extraction system
Room-type dust removal is suitable for the purification of fumes and smoke generated during the production of automated equipment, such as welding robots, welding machines, grinding, grinding and polishing of metal and plastic parts, drilling, thermal processing, cutting and crushing, stone processing, powder packaging, solid particles and various dusts and fumes produced by mixing and processing.
For working conditions such as robot automatic welding, circular seam and longitudinal seam welding, the smoke and dust purifier is installed with the robot workstation, so that the workstation has its own dust removal function. The fume and smoke are effectively collected through equipment components such as pipes and dust hoods. The room-type design prevents the volatilization and diffusion of smoke to keep the air in the workshop clean.
The working conditions with moderate welding workpieces and large amounts of dust and smoke are suitable for room-type treatment solutions. The room type centralized dust dedusting solution is divided into side suction and top suction method dust collecting ways. The appropriate solution can be designed according to the site conditions and treatment goals.
4) Blow suction type fume extraction system
Blow-suction type dust removal solution is a ventilation air flow composed of blown air and inhaled air flow. Therefore, it is a dust removal method that can effectively control the spread of pollution sources. This dust removal method is installing exhaust inlets on two-span center column or single-span side column (wall) and air outlets on the opposite wall column to form a circulating air flow to drive the smoke and dust into the purification machine, consequently performing overall dust removal and purification in the workshop. This system occupies a small area and has obvious purification effect, which is suitable for the purification of smoke and smoke in more complex production workshops.
7. Company information
Jinan Moland Environmental Tech Co., Ltd., is located in No. 11889 Jingshi West Road, Changqing District, Jinan City, Shandong, China, established in 2016. It`s an environmental protection technology enterprise specializing in research, development, manufacture and sale of efficient smoke purification systems.
The company is committed to reducing the environmental impact of production process, protecting workers from harmful gases and dust, and creating a cleaner working environment. At present, the company′s products have been successfully applied in automobile, railway, construction machinery, marine engineering, aviation and other mechanical processing industries, as well as new materials, grain, wood, recycled resources processing and other industries. The company has passed the ISO 9001 quality management system certification, obtained the certification of China Environmental Protection Products issued by China Environmental Protection Industry Association, and CE certification of EU. It also has a number of invention patents, utility model patents and appearance patents. Through continuous R&D and innovation, many products of the company have reached the international leading level.
Moland′s environmental services cover the whole process from project design, product manufacturing to installation, commissioning and after-sales service. We will provide you with the most professional governance program and the best quality service.
External Skeleton Extraction Arms,Mounted Flexible Fume Extraction Arm,Wall-Mounted Flexible Suction Arm,Skeleton External Suction Arm
Jinan Moland Environmental Tech Co.,Ltd , https://www.sdmoland.com