The magnetic flip plate level gauge is installed on the outer extension tube of the tank groove, and the liquid level inside the tank groove is clearly known by the flipper indicator. The outside of the bypass pipe can also be equipped with a magnetic switch as an electrical contact signal output, or a device liquid level transmitter for remote distance level signal transmission and liquid level control. The level gauge is a reliable safety meter. Due to the closed structure of the magnetic coupling separator. Especially suitable for flammable, explosive and toxic toxic level detection. Therefore, the liquid level detection method of the original complex environment becomes simple, reliable and safe. The level gauge has direct reading characteristics of an in-place display.
1. Before using the magnetic level gauge, use the calibration magnet to set the ball below the zero position to red, and other balls to white;
2. If the user uses the heat tracing circuit by himself, non-magnetic materials such as copper tubes must be used. Heating temperature is determined according to the medium condition;
3. The installation position of the magnetic flip plate liquid level gauge should avoid or keep away from the material media entrance and exit, avoid the rapid change of the local fluid of the material fluid, and affect the accuracy of the liquid level measurement;
4. The medium should not contain solid impurities or magnetic substances, so as to avoid jamming of the float.
5, magnetic flap level gauge around the body does not allow access to magnetic materials, disable the wire fixed, otherwise it will affect the normal operation of the magnetic flap level gauge.
6. Open the bottom flange and install the magnetic float (Note: The heavy end is magnetically upward and cannot be inverted.);
7. Open the upper pilot valve first, then slowly open the lower valve to allow the medium to enter the main duct smoothly, observe whether the magnetic red ball is turned properly, then close the lower pilot valve, open the drain valve, and let the level in the main duct drop. , According to this method three times, it is normal, you can put into operation;
8. The magnetic flap level gauge should be cleaned from the main conduit irregularly to remove impurities according to the media condition;
9. For level gauges over a certain length (normal type> 3 meters, anti-corrosion type> 2 meters), an intermediate reinforcement flange or ear climbing needs to be added for fixed support to increase the strength and overcome its own weight;
10. The installation of the magnetic flip plate liquid level meter must be vertical. The ball valve should be installed between the magnetic flip plate liquid level gauge and the container guide pipe to facilitate maintenance and cleaning;
11. When equipped with remote transmission supporting instruments, the following items need to be done: a) The remote transmission matching instrument should be close to the main conduit of the level gauge, and be fixed with stainless steel hoop (disabled iron); b) Remote transmission matching instrument The upper induction surface should face and close to the main conduit; c) The remote instrument supporting zero position should be on the same level as the level gauge zero indication; d) The connection between the remote transmission supporting instrument and display instrument or industrial control computer It is best to put on the protective tube alone or with a shielded two-core cable; e) After the cable entry hole of the terminal box is laid, it is required to be sealed well to prevent infiltration of rainwater, moisture, etc., so that the remote transmission matching instrument can not work normally, and the connection box is in overhaul or After the completion of debugging should be promptly covered.
1. Before using the magnetic level gauge, use the calibration magnet to set the ball below the zero position to red, and other balls to white;
2. If the user uses the heat tracing circuit by himself, non-magnetic materials such as copper tubes must be used. Heating temperature is determined according to the medium condition;
3. The installation position of the magnetic flip plate liquid level gauge should avoid or keep away from the material media entrance and exit, avoid the rapid change of the local fluid of the material fluid, and affect the accuracy of the liquid level measurement;
4. The medium should not contain solid impurities or magnetic substances, so as to avoid jamming of the float.
5, magnetic flap level gauge around the body does not allow access to magnetic materials, disable the wire fixed, otherwise it will affect the normal operation of the magnetic flap level gauge.
6. Open the bottom flange and install the magnetic float (Note: The heavy end is magnetically upward and cannot be inverted.);
7. Open the upper pilot valve first, then slowly open the lower valve to allow the medium to enter the main duct smoothly, observe whether the magnetic red ball is turned properly, then close the lower pilot valve, open the drain valve, and let the level in the main duct drop. , According to this method three times, it is normal, you can put into operation;
8. The magnetic flap level gauge should be cleaned from the main conduit irregularly to remove impurities according to the media condition;
9. For level gauges over a certain length (normal type> 3 meters, anti-corrosion type> 2 meters), an intermediate reinforcement flange or ear climbing needs to be added for fixed support to increase the strength and overcome its own weight;
10. The installation of the magnetic flip plate liquid level meter must be vertical. The ball valve should be installed between the magnetic flip plate liquid level gauge and the container guide pipe to facilitate maintenance and cleaning;
11. When equipped with remote transmission supporting instruments, the following items need to be done: a) The remote transmission matching instrument should be close to the main conduit of the level gauge, and be fixed with stainless steel hoop (disabled iron); b) Remote transmission matching instrument The upper induction surface should face and close to the main conduit; c) The remote instrument supporting zero position should be on the same level as the level gauge zero indication; d) The connection between the remote transmission supporting instrument and display instrument or industrial control computer It is best to put on the protective tube alone or with a shielded two-core cable; e) After the cable entry hole of the terminal box is laid, it is required to be sealed well to prevent infiltration of rainwater, moisture, etc., so that the remote transmission matching instrument can not work normally, and the connection box is in overhaul or After the completion of debugging should be promptly covered.
Roll Trolley,Foldable Warehouse Trolley,Logistics Basket Trolley,Metal Platform Trolley
Suzhou Malltek Supply China Co.,Ltd. , https://www.oktrolley.com